- Motorcykel Dele
- Handles & Kontrol Dele
- Grips
- KIJIMA
- KIJIMA - Grips
- Produkt liste
- Grip Shrink Tube
Grip Shrink Tube
Product # BM-04001
57.4 DKK (1,260 JPY)
List price: 62.86 DKK Save 9%
+13 Webike punkt (0.59 DKK)
Product # BM-04001
57.4 DKK (1,260 JPY)
List price: 62.86 DKK Save 9%
+13 Webike punkt (0.59 DKK)
3.9 / 5
11 anmeldelser
I installed it on my s1000rr.
I have been concerned about Grip wear lately and knew about this product, but had put off purchasing it.
The grip, texture, etc. were both great.View Detail
I purchased the Grip heater because it is more worn than I expected.
The Grip heater used is PLOT's EFFEXGrip heater.
There is also a product for EFFEX in Lineup, but I preferred the look of this one, so I used this product this time.
I was worried about whether it would stick properly because it is quite uneven, but it worked perfectly!
After covering it, the whole thing was then burned with a heat gun.
It may be a little easy to Slip because of its spongy feel.
It is simply a Large Heat Shrink Tube.
I didn't know such a product existed, and if I had known, I would have installed it before it wore out.View Detail
My HondaOEM Sports GripHeater started to slip after about a year of being installed.
This product is attached from above.
It was very effective in terms of preventing slipping, and I didn't have to grip the Grip as hard.
It made the ride very easy.
Heat Shrink Tube in the same manner as the Heat Shrink Tube, aligning and warming it with a Dryer (preferably a Heat gun) will cause it to shrink.
It is a small point, but since it is attached to the original grips, the grips are larger in diameter, so it is necessary to use a larger grips.
The feel of the grip changes considerably.
The Sports GripHeater is sold on the slenderness of its grips.
When I rolled this one up, it was about as thick as a regular Grip heater.
The non-slip effect remains the same even after a year, and if you don't like it, you can cut it off and remove it immediately.
You can also try it easily.
(If you want to increase the non-slip effect/grip diameter (but don't want to change the grips for some reason), you can use the
Very effective product.View Detail
With a heat gun, it takes less than 5 minutes to install, and you only need a heat gun for installation, but the only thing left is durability.View Detail
Bought this to prevent grip wear on my S1000R OEMGrip heater.
Because I had seen the installation article of other people beforehand, I bought Heat gun together and installed it immediately.
Very easy to install, just run it through the Grip and warm it up.
The hang is to apply the warm air of the Heat gun evenly, and it is completed in about two or three minutes of One Side.
The surface seems a little smooth, but if the Gloves are leather, they don't slip, especially
It is available.
If I have one complaint, it's that the price is a little low, as others have commented.
Well, it's a small price to pay for replacing the OEM Grip.View Detail
To continue viewing this product on Japan domestic webike (in Japanese), press "Go to Japan Domestic".
Notification
Vælg mulighed før tilføje til din indkøbskurv.
Kunde service
INFORMATION
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING
* The BEST and MUST store to find Japanese parts.
* Register now for amazing deals and other special offers!
* Over 800,000 listed items. It's hard NOT to find your parts.
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.