This product looks like the original. It adheres to the plastic very firmly. For 3 months of operation of the moped, the appearance of the logo has not changed.
* The BEST and MUST store to find Japanese parts.
* Register now for amazing deals and other special offers!
* Over 800,000 listed items. It's hard NOT to find your parts.
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
This product looks like the original. It adheres to the plastic very firmly. For 3 months of operation of the moped, the appearance of the logo has not changed.
This product are totally superb. Fully satisfied to upgrade your motorcycle. Performance parts that will last longer.View Detail
On the 2001 Honda Forza MF 06, after 15,000 km, the suspension bearing of the right rear wheel hummed. Replaced with NTN products. After that I drove 3000 km, I'm happy with the result. When pressing in the bearing, so that the seat does not wobble, you first need to heat the suspension part with an industrial hair dryer to a temperature of 150 degrees C. This product has a metal protection for the balls, bearings with a plastic ring are installed on the scooter at the factory.View Detail
Fits: YAMAHA TT-R110E 08- [Number of genuine links]90, YAMAHA RZ50 81-89 [Number of genuine links]106, YAMAHA RX80 81 [Number of genuine links]110, YAMAHA RX50 80-81 [Number of genuine links]110, YAMAHA RD50 81-87 [Number of genuine links]112
This chain is used on a Honda MTX 50 and is used in tough off-road conditions. In the mountains, in swampy areas, when overcoming water obstacles up to 0.5-0.6 m deep, the DID STD Series Chain 420D Steel shows itself only positively. It retains its size (does not stretch) when used in enduro conditions no less than for 1000 km.At the same time, it works constantly in mud and with a lack of lubrication.View Detail
After 10 years of operation of the maxiscurator, the grease dried up in the drain bearings and they became unusable. A play appeared on the wheel. I replaced them with Koyo bearings. I need to remove old ones and put new bearings on the wheel’s hot disk, it must be heated with an electric hairdryer. After replacing the bearings Koyo passed 5000 km without any problems.View Detail
On my Honda NSS 250 mf 06 maxiskooter, when the steering wheel was turned too hard, the windshield was touched by the risk of breaking it off. I installed the Ai-net Mirror Adapter (10 mm thread, 1.25 pitch) to the right and left. As a result, the mirrors began to be above the fairing . Adapters are made of high quality, most likely stainless steel. They look good, the exterior of the scooter does not break.View Detail
Fits: SUZUKI RANDY(FM50) *Required number:1, SUZUKI JR50 78 *Number of units required:1, SUZUKI K125 80-94 *Number of pcs required:1, SUZUKI K90 67-91 *Number of pcs required:1, SUZUKI K125 95 *Number of units required:1
Iridium candle was installed on a 2-stroke air cooling Suzuki K 125 motorcycle. The engine on it starts confidently, works well both at medium (3500-4500) and at high speeds (7000-8000). There are no spark plugs in the ignition. The engine pulls well.The carburetor adjusted to a normal mixture, not poor and not rich, brown soot, the motor does not overheat.View Detail
To continue viewing this product on Japan domestic webike (in Japanese), press "Go to Japan Domestic".
Kunde service
INFORMATION
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING